Energy and fuel data for your project sustainability report.
Energy and fuel use is usually the largest controllable source of emissions on a construction site, and the line in a sustainability report that clients ask about first. EnviroTrack records electricity and each fuel against the work package that used it, in the fuel's own unit, so consumption is visible month by month.
How it works.
Each Fuel in Its Own Unit
Litres for diesel, petrol and LPG, cubic metres for natural gas, kilowatt hours for electricity and cylinders for acetylene. Units are never added together.
Source on Every Entry
Each entry is marked meter reading, invoice or estimate, and an estimate carries its calculation.
Renewable Electricity Named
Renewable electricity records its source: a PPA, GreenPower, or another source you name.
Switched On per Package
The head contractor switches on the fuels the project uses, and each package reports only the ones switched on for it.
Location and Use
Every entry carries a date and a location, and can say what the energy was used for, from plant and equipment to light vehicles.
Straight Into Emissions
Once accepted, each quantity is costed with the project’s factors into Scope 1, 2 and 3.
One entry per reading. As many as the month needs.
A package adds an entry for each meter reading, invoice or estimate, with its date, location and quantity. A month can hold several entries for the same fuel.
- An estimate needs its calculation, up to 1,000 characters
- An attached invoice with no source chosen counts as Invoice
- A fuel added as Other must be given its name
Renewable power, kept apart from the grid.
Renewable electricity is its own item, with a source of PPA, GreenPower or one you name. It reports its kilowatt hours and counts as zero Scope 2, so your green power is on record without adding to your footprint.
- Grid electricity carries the project’s electricity factor
- HVO and each biodiesel blend report their own quantities
- Biodiesel, renewable diesel and ethanol add no upstream share
From the total down to each entry.
The Categories tab lists Electricity and Fuel Type with their quantities and emissions. Open a category to see each fuel, and a fuel to see every entry behind it, with the package that reported it.
- The entries always add up to the fuel’s total
- Quantities in different units are never summed
- Download the invoice behind an entry from the list
Every fuel your sites burn, in one list.
The head contractor switches on the electricity and fuels the project reports, and gives each package the ones it uses. Fuels, gases, oils and lubricants each have their own item.
Data Source
- Meter Reading, Invoice or Estimate
- An Estimate Shows Its Calculation
- An Attached File Counts as Invoice
Where and When
- A Date for Every Entry
- A Location for Every Entry
- Several Entries a Month if Needed
Named Items
- A Fuel Type Other Must Be Named
- A Renewable Other Must Be Named
- Units Fixed by the Library
Energy figures with their source attached.
Clients ask where an energy figure came from. In Catchment every entry says whether it was read off a meter, taken from an invoice or estimated, and an estimate shows how it was worked out.
Source on Record
Meter reading, invoice or estimate, chosen on every entry.
Estimates Explained
An estimate cannot be saved without its calculation.
Renewables Named
Renewable electricity carries its PPA, GreenPower or named source.
Counted Once Accepted
Quantities reach the charts only after your team accepts the section.
Why it matters.
Energy and fuel are hard to attribute when they arrive as a quarterly utility bill and a fuel card statement. Catchment records site electricity and fuels by package, and marks each entry as a meter reading, an invoice or an estimate. Renewable electricity and lower-carbon fuels are reported as their own items, so they can be read apart from diesel and grid power. The same data flows directly into Scope 1 and 2 emissions, so your ESG report and your emissions figures are built from one record.
Site and Project Teams
See where energy goes, by package and month.
Sustainability Leads
Report consumption with the dockets and meter reads behind it.
Trade Partners
Log fuel and plant use against their own package.
Energy and fuel, in practice.
Where does the data come from?+
Each package reports its own entries every month. Every entry is marked meter reading, invoice or estimate, and an estimate must show its calculation.
Which fuels can we report?+
Diesel and biodiesel blends, petrol and E10, LPG, natural gas, LNG, CNG, acetylene, hydrogen, HVO, lubricating and hydraulic oils, grease and solvents. A fuel that is not listed can be added as Other, with its name.
Is renewable electricity tracked separately?+
Yes. It is its own item, with a source of PPA, GreenPower or a named other. It reports its kilowatt hours and adds nothing to Scope 2.
Can we record fuel spend?+
No. Energy entries record quantities, not dollars, so fuel spend appears in no EnviroTrack figure.
Why are diesel and electricity not added together?+
They are measured in different units. Each fuel keeps its own total, and only their emissions, in tCO₂e, add up.
Does it feed emissions reporting?+
Yes. Once the section is accepted, each quantity is costed with your project’s factors: fuel into Scope 1 with an upstream share in Scope 3, and electricity into Scope 2 with its own upstream share.
Can trade partners report their own fuel?+
Yes. Each package reports the fuels switched on for it, against its own package, and the head contractor package can report every one the project uses.
See energy and fuel tracking on a real project.
30 minutes with our team, on live project data.
Book a Demo →