Scope 1, 2 and 3 emissions for sustainability reporting in Australia.
Sustainability reporting in Australia now expects emissions figures that can be traced to source. EnviroTrack builds project Scope 1, 2 and 3 emissions from the dockets, invoices and supply-chain submissions your project already produces, so the emissions in your sustainability report break down to package, source and document.
How it works.
Built From Quantities
Emissions come from the litres, kilowatt hours, tonnes and kilometres each package reports, never from what was spent.
One Set of Project Factors
Each project holds its own emission factors, one for each fuel, material and mode, so every package is costed on the same basis.
Scope 1, 2 and 3
Fuel burnt on site is Scope 1 and purchased electricity is Scope 2. Materials, transport, waste and the upstream share of fuel and power are Scope 3.
Figures That Hold
Each entry keeps the factors it was costed with, so editing a factor later does not move a figure already reported.
Only Accepted Data
An entry counts once its package’s Environmental section is accepted, so the charts never show a figure still in review.
Across Every Project
The organisation view adds up emissions across your projects and shows each project against the organisation average.
Report what was used. Catchment does the maths.
A package reports quantities in each item’s own unit: litres of diesel, kilowatt hours of electricity, tonnes of steel, freight and distance for transport. Catchment multiplies each one by the project’s factor for that item.
- Transport multiplies freight by distance before the factor
- Biodiesel and petrol blends are weighed by their share
- An item with no factor reports its quantity and no emissions
Every fuel in the right scope. Upstream included.
Burning diesel, petrol, LPG or natural gas is Scope 1, with the fuel’s upstream share added to Scope 3. Purchased electricity is Scope 2, with its own upstream share. Materials, transport and waste are Scope 3.
- Biodiesel, renewable diesel and ethanol carry no upstream share
- Renewable electricity counts as zero Scope 2
- Water is reported, and never adds to emissions
Change a factor. Past figures stay put.
Your team enters the project’s emission factors once. Every entry is stamped with the factors it was costed with, so a factor edited later applies to new entries and leaves reported months as they were.
- Only a factor above zero counts as entered
- Editing an entry costs it again at today’s factors
- A factor left blank follows the project until the entry is saved again
Everything a site burns, buys and moves.
Emissions build from what each package reports: fuel, electricity, materials, transport and waste, each in its own unit. Water is reported too, and never costed.
Quantity Times Factor
- Each Quantity Meets Its Own Factor
- Transport Is Freight Times Distance
- Blends Weighed by Their Share
Stamped on Save
- Factors Kept on Each Entry
- Later Factor Edits Leave It Alone
- Costed Again Only When Edited
Nothing Guessed
- No Factor Means No Emissions
- Water Is Never Costed
- Spend Is Never Converted
Emissions a client can take apart.
Clients and financiers ask for project-level Scope 1, 2 and 3. Catchment builds each figure from the quantities your packages reported and the factors your project set, and keeps both with the entry.
From Quantities
Scope 3 is built from materials, transport and waste quantities, not from spend.
Counted Once Accepted
Only accepted Environmental sections reach the emissions figures.
Factors on Record
Each entry carries the factors it was costed with.
By Package and Project
Split emissions by package type, and compare each project with the organisation average.
Why it matters.
Project emissions are usually estimated once a year from totals, so nobody can say which package or supplier drove them. That is becoming harder to rely on as ESG reporting requirements tighten under the Australian Sustainability Reporting Standards and as clients and financiers ask for project-level figures. Catchment holds one set of factors per project so every package reports on the same basis, and lets trade partners report their own inputs. Scope 3 is built from supply-chain data rather than spend-based estimates.
Sustainability Leads
Report emissions by scope and package from source data.
Trade Partners
Report fuel, energy and material inputs against their own package.
Clients and Financiers
See accepted figures by scope, and receive the month's export.
Emissions, in practice.
Which emission factors are used?+
Your project’s own. The head contractor enters a factor for each fuel, electricity, material and transport mode the project reports, and every package is costed with the same set.
What happens if a factor changes?+
Entries already saved keep the factors they were costed with. A changed factor applies to new entries, and to an older entry only when someone edits it.
How is Scope 3 worked out?+
From quantities. Materials, transport and waste are each multiplied by their factor, and fuel and electricity add an upstream share. Nothing is estimated from dollars spent.
Why does an item show zero emissions?+
It has no factor. Acetylene, hydrogen, renewable electricity and any item named Other report their quantity and no emissions, and so does an item whose factor has not been entered.
Does water count towards emissions?+
No. Water is reported and charted in kilolitres, but there is no water factor, so it never adds to the total.
When do figures appear in the charts?+
Once the package’s Environmental section is accepted. A section still in review, or sent back, does not count.
Can we see emissions by project?+
Yes. The organisation view shows Scope 1, 2 and 3 across every project, a breakdown by package type, and each project against the organisation average.
See emissions tracking on a real project.
30 minutes with our team, on live project data.
Book a Demo →